The Flyfox 110mm is a BNF Micro 2 inch quadcopter for newcomers HobbyCool.com. I was most interested in this micro quadcopter because so far as I can see, the BNF model here is completely exclusive to HobbyCool.
The frame is based on a 3mm bottom plate with 1.5mm sideplates attached by tabs and 3d printed standoff - very similar to the Leader 120 but with a different look and more importantly, a factory micro CCD camera. The frame with hardware on its own weighs 15g and is available here for less than $10. Speaking of the camera, it looks to be nicely protected by the frame without impacting the view however only a limited amount of camera angle is available as can be seen in the image below:
Electronics are fairly typical - F4 flight control and 20A DSHOT600 ESC. 2 nice suprises I was not expecting here though - tramp control of VTX (my first in a micro) and a baromoter in the flight controler (my first altogether!). ESC uses a JST connect which should be ok although I would have preferred a XT30. Voltage drop may or may not be an issue but in practicality in all except my lightest brushless quads (less than half this weight), it is a much more robust and convinient connector.
This quad is PNP so does not ship with a receiver so I used my favourite XMPlus for FRSKY. It does however ship with a nice 550mah 2s GNB battery which unfortunately for me is still with Hobbycool since getting batteries to where I live (NZ) is getting harder and harder. Lastly a buzzer and 2 x programmable LEDS are connected and mounted and 16 x Kingkong 2035 4 bladed props with screws are included.
All solder joints that I could see looked to be good, wires were well trimmed, routed and secured and the build quality looked good.
All up weight including props, battery strap but no battery is 78g which is heavy but it's worth noting that this is in a power class of it's own with these monstrous motors.
When I first plugged in betaflight configurator in I was expecting to see a dead stock list of settings but was pleased to find some customisation - see below for a list of stock settings which included a number of modes set, craft name, DSHOT600 etc but unfortunately no custom PIDs (or rates). Prior to the initial flight the only changes I made to setting were for my receiver with RSSI set to channel 16 and my stock modes - arm-disarm; angle-horizon-air; beeper off-beeper on.
Getting ready for FPV Maiden
Even before I started FPV I could tell from the hover test that the PIDs were too aggressive by the excessive fluttering I could hear. This is to be expected because the comparitively large motors have absolute control of the motors and so the feedback loop is exaggurated. I knocked P, I and D down for all three axes to get it in the air without risk of damage but it could certainly do with some more tuning to crispen up the controls. Since it was Betaflight 3.2.0 that was installed, PIDs were easily changed via OSD.
Since I did not have the stock 550mah 2S GNB battery (which is highly regarded) I used my turnigy bolt HV 2s 500mah 65c batteries charged to regular voltage with stock jst discharge connectors. For what it is worth, radio was FRSKY QX7s and goggles were the AOMWAY commander V1s. Takeoff weight was 104g
The quad powered on without issue and I was off flying immediately. I started with the stock propellers but switched the the Gemfan 2035 4-blades after finding that they had a bit more top end through a wider blade at the tip. Power was predictably high for a 2 inch but regardless of the large motors lacked a bit compared to a quad swinging a 2.5 inch prop (e.g. leader 120, HGLRC Hornet, Mini Fight). Update: After more time with the Gemfan 2040 Hulkie 3 bladed props I found I was able to get better performance again out of these 3 bladed props over either set of 4 blades. As I suspected when I first reviewed the hulkies, their stiffness and less blades are better suited to a high power setup.
Due to the large motor size response was excellent but given I tend to have a preference for light weight over power I found that hard flying took quite a toll on the batteries. For moderate to heavy flying I found I got about 2 minutes of flight on the 500mah batteries, which recovered to about 3.73 v per cell on resting. During flight though I did get a lot of warning of battery low and land now but in reality just need to change the battery voltage hysterisis setting to be a little more tolerant - article on how to do that here. Update: 15 packs later I consistently get 2 minutes on these batteries.
It is fair to say that between the large stator height of 6mm and very high kV of 7800, this motor is designed for 2s and no more - even trying 3s did not cross my mind... not only because of the likelihood of the motor cooking itself but because you simply cannot take advantage of it with the 2 inch props - it will just make more noise and heat.
Batteries and motors aside, the quad feels like any other high powered 2 inch - powerful but certainly not floaty where you need more throttle to make it change direction. Camera performance was on par with other CCD micro cameras including the Runcam swift micro, Foxeer arrow micro, HGLRC Elf, Furibee MS 1672. Video signal was good - typical for a dipole but like that it had the option of switching by 25mW-100mW-200mW via tramp protocol in the ESC. To be consistent with other reviews I stuck with 25mW. It's worth mentioning that when the vtx dipole is laying flat against the quads as in my pictures the reception is poor. Even when I temporarily bent it up performance improved a lot, but will cover this more in my list of recommendations.
The Flyfox 110mm BNF from Hobbycool is a high powered 2 inch drone that is well built and fairly priced at $129 the time of writing. It's key feature is the massively powerful 1106 AOKFLY motors that are fast but make the quad heavy and limits battery choice to 2s, even though the electronics can take up to 4s. These features make for a fast quad in a straight line that needs extra throttle in corners to help keep a line. The downside is that battery life is shortish - 2 minutes flat out on a 500mah battery. The kit is well provisioned with 16 propellers in total and a very nice 2s 550mah GNB battery.
The FlyFox 110mm BNF Micro brushless quadcopter is available exclusively at HobbyCool.com I'd like the thank Kevin for the sample he provided for me to review.
Just a guy reviewing RC Quadcopter stuff