The Beebee 66 is a micro 1s brushless powered quadcopter which is essentially a brushless Tiny Whoop. It is made by Full Speed RC, the same company that produced the highly successful Leader 120. (review here). Gearbest kindly supplied me a BNF Beebee 66 to review. I was desperately hoping for this to be the brushless answer to the tiny whoop but I'm really bummed out that it just isn't. Read on to find out why.
Adding a receiver
Since this was supplied as a BNF model, it came without a receiver. I opted to use the lightest FRSKY receiver I had on hand - an XM that I'd finally figured out how to fash with the RSSI channel 16 firmware. In most models this is a matter of soldering wires to the exposed pads on the top of the flight controller. However,since the FC and ESC are part of the structure of this quad AND the FC is flipped upside down to sit the ESC connector in a manageable location, the prop gaurd, 4 nylon nuts and the flight controller itself had to be removed before I could access the receiver solder pads. Then I needed the help of a multimeter to figure out ground, +5v and signal wires. Once soldered up with a short length of silicon wire to the receiver it was easy enough to re-assemble and tuck the XM reciever underneath the canopy behind the AIO camera/VTX. Pics below of course can explain this better:
It's not the end of the world wiring in a reciever here but can be fiddly with particularly small hardware. I'd recommend if you did buy this model that you purchase with the receiver of your choice pre-fitted.
Kept it pretty simple here. Because this is quite a different steup than I am used to I retained the stock settings on Betaflight 3.1.7 that it arrived with. All I did was set an arm switch and a mode switch for angle-horizon-air. Below are the default settings from Betaflight 3.1.7. Oh yeah, receiver had to be set up too. Like most f3 boards receiver is on UART 3.
The only other preparation was pretty straighforward. The included GNB High Voltage 1s 260mah Lipo battery was easily charged using the included USB adaptor and a micro usb cable I had on hand. Only 1 set of props was included that are press-fitted on the tiny 0705 fullspeed branded (Sunny Sky made) 0705 brushless motors. I left the VTX on the default channel for the initial flight that my Aomway Commanders (review here) picked up as 5905MHz.
Please look away if you love your Beebee 66 because it starts to get a bit ugly here. After fully charging the LiHV batteryand confirming everything was working ok I armed and found the props were fouling on the TPU canopy. Minor annoyance down to the tight tolerance in the slightly flexible TPU canopy. Easy enough to bend out of the way and I was back in action.
The first thing I noticed how loud the motors are - not in idle where they are practically silent but under any sort of load. Next as part of test with line of sight attempting a 'punchout' I could clearly see the quad dipping (pitch/roll) and twisting (yaw) under load. I'll attempt to tune this out later on and will post another review if successful. Moving on to line of sight I found the flight performance dull and uninspiring. What's worse was that after just one and a half minutes flight my battery was sagging down below 2.7v - the motors were clearly very demanding for their relatively mild output. I really wanted this quad to be a success and in fairness there is a chance I could have a less than perfect unit but my experience is my experience and I was disappointed. I do have some thoughts on how to improve though and I'll cover this in my Next Steps section below.
Comparison to a brushed micro
Please understand that these comments aren't made from isolation - I've had some experience with tiny whoops based on 7mm motors (like the JJRC H67 or Eachine E011) and although these are cheap brushed toy grade quads, they offered equivalent or better power and a flight time of 4 minutes plus on the same size battery with much smoother flight performance. A quick note that I actually tried the stock battery from the JJRC H67 (260mah non-HV) and got only 1 minute flight before it sagged below 2.7v under load. After recovery it bounced back to 3.65V but this same battery give my 4 minutes plus in my E011 FPV or santa whoop.
At this point I can't recommend this quad. The performance I experienced was poor and the flight time was unacceptable. My guess it that the brushless motors do not scale down well to 7mm, at this size the brushed motors seem to be more approprate. I'd recommend going in one of two directions:
I'm not content to leave things be with the Beebee 66 and the latest version of this model (Beebee 66 lite) has shown the direction I want to go in - removing weight. I'm skeptical of getting to the level of improvement I want but with some of the parts below I think I can replace the canopy with a simple camera holder. remove the propgaurd and TPU supports and save up to about 4g. Will this make enough difference? Not sure but will report back when I'm done. Make sure you bug me about the follow up in the comments if I'm too slow! Below are some of the weights of the components I'm interested in:
Just a guy reviewing RC Quadcopter stuff